Welcome, Guest Login

Support Center

N-Routers Port Forwarding

Last Updated: Oct 23, 2013 06:31PM COT
NexxtLogo

This article applies for Nebula150, Stealth150, Solaris300, Nyx150, Tarvos300, Acrux300, Polaris150 and Viking150.

NOTE: Your N Router is compatible with any Operating System for setup, it only requires a internet browser to access it. ( IE, Mozilla, Firefox , Chrome, Safari, etc) 
 
 
If you don't know which firmware version has your router, before proceed first check this link to know the Firmware version of your router model: Which router firmware do I have?

 
Please go to the link regarding your router firmware to know the steps to setup your Virtual Server (known as Port Forwardding) and enable a TCP Server, FTP Server or another external IP Service (IP Cameras, Remote desktops, etc).

Port Forwarding for Vertical Firmware router models


Port Forwarding for Horizontal Firmware router models

Port Forwarding for Default Firmware router models

 


 
 

Port Forwarding for Vertical Firmware Models
 

1. Create your internal server, make sure the LAN users can access these servers and known related service port. For example, Web server’s port is 80; FTP is 21; SMTP is 25 and POP3 is 110. One case is the Slingbox port that is 5001. For other services such as IP Cameras, the port was given by device and port can be modified on the device itself by customer.
 

2. Open your browser (IE,Mozilla,Firefox,etc) and enter the IP address of the router "192.168.0.1" by default. This will prompt you to type some credentials to access the router webpage. Use "admin" as user and password.

 
3. On your router’s web click “Virtual Server".

4. Select “Port Range Forwarding”. 
 

 
4. Input the external service port on "Start port - End Port" given from the device or service. If the service use a port range, place your range limits here. If the service uses an unique port, place this port on both fields.
 
5. Input the IP address that the service adquires from the router IP range. For example, if your Web server’s IP address is 192.168.0.10 inside the router's network, please input it to be declared on your DHCP internal table with the assigned service port.
 
7. Select the communication protocol used by your internal host: TCP, UDP or both (Recommended).

8. Choose "Enable" to activate the port or "Delete" to deactivate the port forwarding.

9. Click “Apply” to save your settings.


Go Back

 
 

Port Forwarding for Horizontal Firmware Models

1. Create your internal server, make sure the LAN users can access these servers and known related service port. For example, Web server’s port is 80; FTP is 21; SMTP is 25 and POP3 is 110. One case is the Slingbox port that is 5001. For other services such as IP Cameras, the port was given by device and port can be modified on the device itself by customer.

2. Open your browser (IE,Mozilla,Firefox,etc) and enter the IP address of the router "192.168.0.1" by default. This will prompt you to type some credentials to access the router webpage.

3. Use "admin" as password.

4. On the router's webpage, go to "Advanced settings" at the middle of the webpage.


5. On your router’s web click “Virtual Server” and select “Port Range Forwarding”. 
 
 
6. Input the external service port on "Start port - End Port" given from the device or service. If the service use a port range, place your range limits here. If the service uses an unique port, place this port on both fields.
 
7. Input the IP address that the service adquires from the router IP range. For example, if your Web server’s IP address is 192.168.0.10 inside the router's network, please input it to be declared on your DHCP internal table with the assigned service port.
 
8. Select the communication protocol used by your internal host: TCP, UDP or both (Recommended).

9. Choose "Enable" to activate the port or "Delete" to deactivate the port forwarding.

10. Click “OK” to save your settings.


Go Back
 
 

Port Forwarding for Default Firmware Models

1. Create your internal server, make sure the LAN users can access these servers and known related service port. For example, Web server’s port is 80; FTP is 21; SMTP is 25 and POP3 is 110. One case is the Slingbox port that is 5001. For other services such as IP Cameras, the port was given by device and port can be modified on the device itself by customer.

2. Open your browser (IE,Mozilla,Firefox,etc) and enter the IP address of the router "192.168.0.1" by default. This will prompt you to type some credentials to access the router webpage.

3. Use "admin" as user and password.

4. On your router’s web click “Forwarding” and select “Virtual Servers”. 


5. On "Virtual Servers", click on "Add new".


6. Input the external service port on "Service port" given from the device or service. 

7. Input the Internal service port on "Internal Port" given from the device or service. This is valid just for a Single Service port, you can repeat the Service Port or leave blank.

8. Input the IP address that the service adquires from the router IP range. For example, if your Web server’s IP address is 192.168.0.10 inside the router's network, please input it to be declared on your DHCP internal table with the assigned service port.
 
9. Select the communication protocol used by your internal host: TCP, UDP or All (Recommended).

10. Choose "Enable" to activate the port or "Disable" to deactivate the port forwarding.

11. Click “Save” to save your settings.


Go Back

Contact Us

  • Email Us
  • Live Chat!
techsupport@nexxtsolutions.com
http://assets0.desk.com/
false
assistly
Loading
seconds ago
a minute ago
minutes ago
an hour ago
hours ago
a day ago
days ago
about
false
Invalid characters found
/customer/en/portal/articles/autocomplete