Welcome, Guest Login

Support Center

AMP300: Repeater Settings

Last Updated: Mar 20, 2019 01:39PM COT


NOTE: Your new router is compatible with any Operating System, it only requires a browser to access the configuration website. (IE, Firefox, Opera, Chrome, Safari, etc).

 
Recommendations: We recommend to work with the AMP300 stand-alone. This is because sometimes the PC or Laptop are connected to a Wireless Signal or via LAN to the main router or modem. If you are using a Laptop or PC with Wi-Fi signal, please disable the Wi-Fi or turned Off. This article will set up the AMP300 via Ethernet cable. 

Requirements: 

 
  • PC or Laptop (remember to disable the Wi-Fi)
  • AMP300
  • Ethernet cable (this will come in the box)
  • Power Adapter (this will come in the box)
 
NOTE: If you are using a Laptop or PC and do not have the Ethernet Port you will have to connect the PC or Laptop via wireless. All you have to do is the following.
 
  • Turn ON the Wireless or Wi-Fi on the Laptop or PC. 
  • Search for networks in the vicinity
  • You will see the name of the SSID provided by the AMP300. This will be something like Nexxt_XXXXXX (where the Xs are the last 5 to 6 digits of the MAC Address of the AMP300) To be sure which it is, take the AMP300 in your hand and turned over and you will see an orange sticker that will contain information about the AMP300. Look for the MAC Address.
  • Choose the network, and connect the PC or Laptop to it and you are done.

Steps:
 
1. Connect the power adapter to the AMP300. This will turn On the device.
 
2. Press the RESET/RST button for 20 seconds. This will reset the AMP300 in case you have done any changes and you didn´t notice.
 
3. Take the Ethernet cable in your hand, one end of the cable goes to the LAN Port #1 in the AMP300 and the other end goes to the Ethernet Port on the PC or Laptop.
 
4. Once you are connected either Wi-Fi or Ethernet, open your browser and type the IP Address 192.168.0.1 press the key ENTER.
 

 
5. If you have done all the steps correctly, you will get a prompt window asking you to sing in by typing the Username and Password so proceed to type admin in both fields. This information also appears in the guide and bellow the AMP300.
 

 
6. Once you pass the sing in prompt you will see the configuration website. 
 

7. Once inside choose the  Repeater option. 
 

8. Here you will have several options to choose or do. There is 3 field here.

- The first one will tell you the default IP Address the AMP300 is using. Do not change this, unless the AMP300 default IP is the same as the main modem and is causing you conflict. 

 

 
- The second one is the settings to secure the wireless signal the AMP300 is providing. Here you can proceed to change the default name from Nexxt_XXXXXX to another one you want. And also change the default password 12345678 to any password you desire.
NOTE: We strongly recommend to use the same password of the main router/modem Wi-Fi so you do not need to have several passwords to remember.
 

- In the third part is where you setup the repeater steps, so the  AMP300 can repeat the internet from the main Wi-Fi signal or the signal you want him to repeat.
 

9. Press the Site Survey to scan the area for wireless signals close to the AMP300. Proceed to choose the signal. 
 

 
10. Once you choose the signal, proceed to add or fill the Security Mode and Encryption Type and the Wi-Fi password of the wireless you want to repeat in the Passphrase field.
 

 
11. After that press Save/Apply to save the settings and you AMP300 will start repeating the internet. 

Contact Us

  • Email Us
  • Live Chat!
[email protected]
http://assets3.desk.com/
false
assistly
Loading
seconds ago
a minute ago
minutes ago
an hour ago
hours ago
a day ago
days ago
about
false
Invalid characters found
/customer/en/portal/articles/autocomplete